This website uses cookies to ensure you get the best experience on our website. Using this website means you're OK with it.

Luck 3 (110м²)

Рейтинг: 3.27/5 (33 Votes)
icon zoom
Main facade Rear facade
Cottage with four bedrooms:
  • Total area:110 м²
  • House dimensions:8.8 м х 8.2 м
CONSTRUCTION:
  • Foundations:Pier
  • Exterior Walls:Timber frame 350 mm
  • Overlaps:Wooden joist, No
  • Roof:Pitched
  • Roofing:Bitumen tile
Cottage with four bedrooms Luck 3
Project price:
478
Buy Project
home project plan, luck 3
NameSq.m
1Hallway 8.1
2Half-bathroom 2.3
3Corridor 3.0
4Staircase 4.8
5Study room 9.9
6Dining-room 29.4
Total floor area57,5
home project plan, luck 3
NameSq.m
1Corridor 4.6
2Half-bathroom 6.2
3Walk-in closet 2.7
4Bedroom 15.2
5Bedroom 14.1
6Bedroom 9.9
Total floor area52,7
Input data and construction description
Parameter data
Soil carrying capacity
Foundations Pier
Walls Timber frame 350 mm
Roofing Bitumen tile
Number of floors 2
First floor floor Reinforced concrete panels
Ground floor height 2.8 м
The height of the second floor 2.7 м
Overlap of the first floor Wooden joist

The project of frame house with a shed for car, four bedrooms and a large kitchen-living room

 

Frame house plans with capony - Luck 3

 

The main idea of ​​this frame house project is simplicity in construction and maximum convenience for residents. Such a house is perfect for use as a residential building for permanent residence, or a country cottage. The dimensions of the structure are 8.2 x 8.75 m in plan. On one side of the house is a canopy for car storage. The width of the canopy is 3.4 m, the length is 8.75 m. Under such a canopy there is enough space for a car and, for example, a motorcycle or walk-behind tractor.

The house is two-story. In front of the house is a porch covered with a gable roof. The floor height of the premises from the ground is 73 cm. The following premises are provided on the ground floor: entrance hall, bathroom, living room, living room combined with kitchen and stairs to the second floor. In the hallway there is a place to place a wardrobe for outerwear. The kitchen-living room area is 29.4 m2. The living room can be used as a bedroom for guests or an office. This small room has an area of ​​9.5 m2. It is possible to organize a second exit from the kitchen to the garden and make a terrace. The total area of ​​the first floor is 57.5 m2. The ceiling height of the first floor is 2.5 m.

The second floor is the attic. The height of the wall, where the roof begins, is 1.7 m. On the second floor there are three bedrooms, a hall, a bathroom, a dressing room. Two large bedrooms have an area of ​​14 and 15 m2. The smaller bedroom, designed for one person, has an area of ​​9.5 m2. The total area of ​​the second floor is 52.7 m2. The height of the premises is 2.5 m. The structural design of the building is with longitudinal supporting walls. Walls of frame construction made of wooden, elements, floors on wooden beams, roofing on wooden rafters. Foundation column made of monolithic reinforced concrete. On top of concrete pillars is a crossbar made of monolithic reinforced concrete.

The project provides that the foundation of the foundations is dry soil, not subsiding with a bearing capacity of 1.7 kg / cm2, the freezing depth is 1 m. For a relative mark of 0.000, take the clean floor level of the first floor. The construction of foundations must be adjusted according to the results of geological surveys at the construction site. In order to prevent subsidence and cracking of the floor from under the house, it is necessary to remove the vegetative layer. Along the perimeter of the house, make a blind area 1.5 m wide.
The floor of the first floor is wooden beams. Under the floor is a ventilated technical underground. External and internal load-bearing walls of frame construction made of wooden elements. Frame elements should be made of pine with a humidity not exceeding 17%. Use Rockmin basalt wool slabs as insulation. The thickness of the insulation of the outer walls is 250mm. Outside the walls sheathe OSB boards, inside - with drywall. Inside the premises, the outer walls are sheathed with vapor barrier made of plastic film. Glue the joints of the film with construction tape. Externally, mineral wool sheathed with a layer of windproof film.

In order to ventilate the insulation between the insulation and OSB, provide a 30mm layer of air which is connected to the outside air with ventilation holes. Holes ∅25 at the rate of 5 holes per 1 running meter.roztashuvata above the base and under the roof overhangs. Drywall partitions on steel profiles or wooden slats. Lay mineral wool slabs inside the barrier.

Overlap the first to perform on wooden beams. The floor of the attic is wooden. Overlappings of the attic and the roof are insulated with Rockmin basalt wool slabs comrade 300 mm. On the overlap in the bathrooms of the first and second floor, lay a waterproofing. Lay a reinforced cement-sand screed 50 mm thick on top of which ceramic tiles are laid. Plasterboard degeneration in bathrooms should be treated with a primer and waterproofing like SR-65.

Rafters wooden, a covering - a metal tile. The rafters should be secured with twisted wires of 2Ø4ВР 1 wire to the frame elements. Rafters made from pine with a moisture content of not higher than 17%. Before use, treat wooden elements with an antiseptic and a flame retardant. Wooden elements that collide with concrete and brick structures should be closed with rubiroid at the junctions and antiseptic. Place wood elements at a distance of at least 380 mm from the inner surface of the smoke channel.

The source of heat supply and hot water supply is a gas double-circuit boiler, which is located in the kitchen. The pipe for the removal of combustion products is connected to the smoke channel, which must be equipped with a revision with an opening for the removal of condensate. For heating and hot water it is possible to use electrical appliances and a boiler. Water supply to the house from an external water supply network or well. Enter a water pipe into the house under the foundation at a depth of at least 1.8 m. Sewerage - with the help of local treatment facilities made of reinforced concrete or plastic septic tank and filter wells.

Gravity drainage network made of polyethylene pipes PND "S". The depth of the sewer pipes is not less than 0.9m. The places of conclusions and releases of engineering communications should be determined according to the conditions and location of the house on the plot. To ensure normal sanitary and hygienic conditions in the premises, the project provides ventilation with natural motivation. The supply air in the volume of a single air exchange enters through the windows, removal through the built-in ventilation ducts. Ventilation of bathrooms is assumed to be integrated ventilation ducts.

In the boiler room, a ventilation duct ∅130mm is arranged, which is discharged above the roof by 0.7 m. For ventilation of the kitchen, one ventilation duct is provided for general ventilation, and the other for attaching an exhaust hood with a built-in fan. In the case of installing windows without windows and with an airtight nest, window modifications with built-in ventilators are used.

If you need a frame house project with a boiler room and a terrace, see the Bucha project 113 m2. This project can be viewed here.

See also attic frame house plans - Rakita - 110 sqm

Look at other ready to use frame house projects

Leave your comment

(will not be shared)

You have watched these projects

top arrow
up